ANSI LC 4-2007


Click to enlarge $230.00

Documentation
Add to Cart:


NOTE: Our website provide PDF immediately download,sometimes when you purchased can't online download please contact us,we will send the document to you with email.

NOTE: in order to view PDFs you will need to have the FREE Adobe® Reader® installed, click the ""

 ANSI LC 4-2007

Press-Connect Copper and Copper Alloy Fittings for Use in Fuel Gas Distribution Systems
American National Standards Institute / 29-Jan-2007 / 48 Pages
Description
This publication represents a basic standard for safe operation, substantial and durable construction, and acceptable performance of gas-fired pool heaters. It is the result of years of experience in the manufacture, testing, installation, maintenance, inspection and research on gas-fired pool heaters designed for utilization of gas. There are risks of injury to persons inherent in appliances that, if completely eliminated, would defeat the utility of the appliance. The provisions in this standard are intended to help reduce such risks while retaining the normal operation of the appliance.

Nothing in this standard is to be considered in any way as indicating a measure of quality beyond compliance with the provisions it contains. It is designed to allow compliance of gas-fired pool heaters, the safety, construction and performance of which may exceed the various provisions specified herein. In its preparation, recognition has been given to possibilities of improvement through ingenuity of design. As progress takes place, revisions may become necessary. When they are believed desirable, recommendations or suggestions should be forwarded to CSA America, 8501 East Pleasant Valley Road, Cleveland, Ohio 44131, or the Chairman of Canadian Standards Association Gas Equipment Standards Technical Committee, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6.

Safe and satisfactory operation of LC 4 Press Connect Copper and Copper Alloy Fittings depends to a great extent upon its proper installation, use and maintenance. They should be installed, as applicable, in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54; the Natural Gas and Propane Installation Code, CSA B149.1.

Users of this American National Standard/Canadian Standard Association Standard are advised that the devices, products and activities within its scope may be subject to regulation at the Federal, Territorial, Provincial, state or local level. Users are strongly urged to investigate this possibility through appropriate channels. In the event of a conflict with this standard, the Federal, Territorial, Provincial, state or local regulation should be followed.

THIS STANDARD IS INTENDED TO BE USED BY THE MANUFACTURING SECTOR AND BY THOSE APPLYING THE EQUIPMENT AND BY THOSE RESPONSIBLE FOR ITS PROPER INSTALLATION. IT IS THE RESPONSIBILITY OF THESE USERS TO DETERMINE THAT IN EACH CASE THIS STANDARD IS SUITABLE FOR AND APPLICABLE TO THE SPECIFIC USE THEY INTEND.
This standard applies to copper and copper alloy press-connect type fittings,and valves(hereafter referred to as fittings unless otherwise specified) for use with fuel gas tube systems intended for installation above groud,below groud,indoors and outdoors.

Featured Products: ASME BPVC-2015 , ASME B31.3-2014 , AWS D1.1/D1.1M-2015 , ASME B31.1-2014 , ASME A17.1-2013 , ASME B16.34-2013 , ASME B16.5-2013 , ASME B31.9-2014 , API STD 650-2014 , API STD 1104-2014 , ISO 9001-2015 , BS PD 5500-2015

Recommend Products


ANSI Z21.20-2005
$132.00

ANSI Z21.74a-2010
$35.00

ANSI Z21.74-1992
$232.00

ANSI Z21.23-2010
$215.00

ANSI Z21.42-1993
$132.00

ANSI Z83.18-2004
$322.00

ANSI Z21.20a-2008
$40.00

ANSI LC 6-2008
$220.00